BWCVG - FE-7004-A RESIWELD

  • MSDS: BWCVG
  • Manufacturer: H B FULLER CO
  • Product Name: FE-7004-A RESIWELD
  • National Stock Number: 8040-00-062-4173
Product Identification

Product ID:FE-7004-A RESIWELD
MSDS Date:03/29/1994
FSC:8040
NIIN:00-062-4173
Kit Part:Y
MSDS Number: BWCVG

Responsible Party
H.B. FULLER CO.
1200 WOLTERS BOULEVARD
VADNALIS HEIGHT, MN 55110
US

Emergency Phone: 612-481-3300 OR 612-488-1588

Info Phone: 612-481-3300

Preparer: INDUSTRIAL HYGIENE

Cage: DO317

Contractor
H.B. FULLER COMPANY
ST. PAUL, MN 55126-8076 US

Telephone: 612-236-5300/ -5309 FAX

Cage: 0DH19

Ingredients

N-BUTYL GLYCIDYL ETHER (BGE)

CAS: 2426-08-6

RTECS: TX4200000

Fraction By Weight: 1-10%.

OSHA PEL 50 PPM

ACGIH TLV: 25 PPM; 9394


EPOXY RESIN

Fraction By Weight: 70-100%

OSHA PEL NONE ESTABLISHED

ACGIH TLV: NONE ESTABLISHED


SILICA GEL

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 1-5%


90 G/L

RTECS: 9999999VO

Hazards

Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION MAY CAUSE RESPIRATORY TRACT
IRRITATION AND CNS EFFECTS. CONTACT MAY CAUSE SKIN SENSITIZATION
AND EYE IRRITATION. HARMFUL IF SWALLOWED. CHRONIC: LONG-TERM
OVEREXPOSURE TO SOLVENTS MAY CAUSE LIVER & KIDNEY DAMAGE.
Explanation of Carcinogenicity:NO INGREDIENT OF A CONCENTRATION OF 0.1%
OR GREATER IS LISTED AS A CARCINOGEN OR SUSPECTED CARCINOGEN.
Effects of Overexposure:EYES: REDNESS, TEARING, BLURRED VISION. SKIN:
REDNESS, RASH, DISCOMFORT. INHALED: DIZZINESS, HEADACHES, NAUSEA,
UNCONSCIOUSNESS.
Medical Cond Aggravated by Exposure:NO KNOWN EFFECTS ON OTHER
ILLNESSES.

First Aid

First Aid:INHALATION-REMOVE TO FRESH AIR. RESTORE BREATHING IF NEEDED.
CALL A PHYSICIAN. EYE-IMMEDIATELY FLUSH WITH WATER FOR 15 MINUTES.
CALL A PHYSICIAN. SKIN-WASH WITH SOAP & WATER. REMOVE CONTAMINATED
CLOTH ING. INGESTION-DO NOT INDUCE VOMITING. GET MEDICAL ATTENTION
IMMEDIATELY. NEVER GIVE ANYTHING BY MOUTH TO UNCONSCIOUS PERSON.

Fire Fighting

Flash Point Method:PMCC
Flash Point:173F,78C
Extinguishing Media:USE WATER SPRAY, FOAM, DRY CHEMICAL OR CARBON
DIOXIDE.
Fire Fighting Procedures:PERSONS EXPOSED TO PRODUCTS OF COMBUSTION
SHOULD WEAR SELF-CONTAINED BREATHING APPARATUS & FULL PROTECTIVE
EQUIPMENT.
Unusual Fire/Explosion Hazard:THERE IS A POSSIBILITY OF PRESSURE
BUILD-UP IN CLOSED CONTAINERS WHEN HEATED. WATER SPRAY MAY BE USED
TO COOL THE CONTAINERS.

Accidental Release

Spill Release Procedures:ELIMINATE ALL SOURCES OF IGNITION. VENTILATE
AREA. AVOID BREATHING VAPORS. DIKE & CONTAIN SPILL WITH INERT
ABSORBENT & TRANSFER TO CONTAINER FOR DISPOSAL. USE NON-SPARKING
TOOLS. KEEP SPILL OUT OF SEW ERS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE AWAY FROM
STRONG OXIDIZING AGENTS AND SOURCES OF IGNITION. KEEP CONTAINER
CLOSED.
Other Precautions:EMPTIED CONTAINER RETAINS VAPOR AND PRODUCT RESIDUE.
OBSERVE ALL LABELED PRECAUTIONS UNTIL CONTAINER IS CLEANED. DO NOT
CUT OR WELD NEAR OR ON THIS CONTAINER!

Exposure Controls

Respiratory Protection:IF ENGINEERING CONTROLS DO NOT MAINTAIN
INHALATION EXPOSURES BELOW PEL/TLV, USE NIOSH/MSHA APPROVED
RESPIRATOR AS PER CURRENT 29CFR1910.134, INSTRUCTIONS/WARNINGS &
NIOSH-RESPIRATOR DECISION LOGIC-PUB #87-108.
Ventilation:PROVIDE SUFFICIENT GENERAL/LOCAL EXHAUST VENTILATION IN
PATTERN/VOLUME TO CONTROL INHALATION EXPOSURES BELOW PEL/TLV.
Protective Gloves:IMPERVIOUS TYPE FOR TASK AT HAND.
Eye Protection:SAFETY GLASSES.
Other Protective Equipment:AS REQUIRED FOR TASK AT HAND TO MINIMIZE
EXPOSURE & ENHANCE WORKER PROTECTION (EG. EYE-WASH STATION, ETC).
Work Hygienic Practices:USE IN MANNER SET FORTH BY MFR'S DIRECTIONS AS
WELL AS PROCEDURES SET FORTH BY SAFETY & HEALTH OFFICE.
Supplemental Safety and Health
WARNING STATEMENTS: VAPORS HARMFUL-DERMAL SENSITIZER. KEY1:F8.

Chemical Properties

HCC:V4
Spec Gravity:1.15
Viscosity:3500 CPS
Appearance and Odor:MILKY WHITE LIQUID, SWEET ODOR.

Stability

Stability Indicator/Materials to Avoid:YES
NOT ESTABLISHED.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NOT ESTABLISHED.

Disposal

Waste Disposal Methods:DISPOSAL VIA INCINERATION AT AN APPROVED
FACILITY IS RECOMMENDED. DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE
AND FEDERAL REGULATIONS. NOT REGULATED AS HAZARDOUS WASTE UNDER 40
CFR 261.

======================================================================
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.